Private website concept.

New London Solar

Waterford, Connecticut

Solar Installer in Waterford, CT: Separate Solar and Backup Quotes

Before you ask a Waterford installer for quotes, check whether any part of your house is in a mapped flood zone. Then ask for a solar-only quote and a separate, optional backup quote for chosen circuits, as the proposed New London Solar service would. Waterford's permit fee, flood-zone test and price check use those lines.

  • For Waterford homeowners weighing solar and backup
  • A solar quote and optional backup quote
  • Check flood rules and price before signing

Get your free quote

Simplified map of the Connecticut shoreline around the Thames River with Waterford highlighted in amber.
Waterford sits 2.6 miles from New London City Hall in a straight line. Simplified map from U.S. Census Bureau boundaries; it shows no parcels or zoning.
On this page 8 sections

Check your flood status before you ask for quotes

Start with one question, because it decides how much of this page applies to you: is any part of your house inside the Special Flood Hazard Area (SFHA)? That is the land FEMA maps as having a 1% chance of flooding in any given year. Base flood elevation (BFE) is the height water is expected to reach in that flood.

This isn't only a question for houses on the water. Waterford's 2012 hazard mitigation plan counted about 310 structures in the 1% floodplain: 269 in AE zones, 31 in coastal VE zones, and the rest in Zone A or the floodway. The plan noted that most of the AE structures face inland flooding rather than waves off Long Island Sound. Those figures are from 2012, measured against a flood map then dated July 18, 2011. Use them to judge scale. They can't tell you whether your address is in.

Waterford draws the line generously. Under §25.3.3(F) of the Waterford Zoning Regulations (effective June 5, 2026), if any portion of a structure sits in the SFHA, the entire structure is treated as being in it, attached garages and decks included. A house whose back deck crosses the mapped line counts as in.

How to check:

  1. Look up your address on FEMA's Flood Map Service Center. Note the zone and the effective date of the map panel.
  2. If any part of the house, attached garage or deck looks mapped, or you can't tell, ask Waterford's Zoning Official. The town's flood-zone instructions name that office for these questions.
  3. Give the answer to every installer you ask for a quote, so their paperwork starts on the right route.

If the house is in a mapped flood zone, read every section below. The zoning compliance permit, the 50% test and the equipment-height rules all apply. If it is clear, skip the 50% section: the permit fee, price check, backup design and utility choice still depend on how the quote is split.

Waterford's permit route: zoning compliance first in a flood zone

Solar systems are on Waterford's list of work requiring a permit. The Waterford Building Department takes applications online through CITY SQUARED, the town's permit portal, or in person at the building office in Town Hall, 15 Rope Ferry Road. Every application needs a cost estimate.

Two permits can be involved. A zoning compliance permit confirms the project meets zoning, including the flood-hazard rules. A building permit lets work start and leads to inspection.

In a designated Flood Hazard Area, §25.3.3(D) of the zoning regulations requires a zoning compliance permit before any building permit is issued, for construction of any nature. A rooftop array is included. Outside a flood hazard area, this flood-specific step doesn't apply, though it is worth asking the Building Department whether your lot needs any other zoning sign-off.

For work on an existing building in a flood zone, Waterford's Information for Work in a Flood Zone packet asks for:

  • exterior photos of the building;
  • a detailed description of the work;
  • a cost estimate;
  • signed, notarized affidavits from both the owner and the contractor.

The packet also says that work added later triggers a fresh evaluation. If you add panels this spring and a battery next year, the town looks again at the combined total.

What the permit fee depends on

Waterford's permit fee schedule charges $20 for the first $1,000 of building cost, plus $10 for each further $1,000 or fraction of it, plus a State fee of $0.26 per $1,000. Electrical and other trade costs can be deducted from the building cost if the estimate lists them as separate line items. Zoning and land-use fees are charged separately.

Illustrative calculation, Waterford building permit fee. On a solar-only estimate of $28,500 (illustrative): $20 for the first $1,000, plus 28 × $10 for the remaining $27,500 (27 full thousands and a fraction) = $300, plus the State fee of about $7.50. Fold a battery and subpanel into one $44,400 figure with no separate trade lines, and the same formula gives a building fee of $460.

The electrical work still gets permitted and charged. Separate lines only decide which permit each dollar lands on. Ask the Building Department how it charges the trade lines you deduct.

Historic review is unlikely to enter the route. Waterford's Historic Properties Commission oversees two individually designated properties, not a district of homes.

Who files what

The proposed New London Solar service (Proposed service) would hand you a responsibility sheet naming an owner for each line. Whoever you hire, ask for the same thing in writing:

Step Applies when Suggested owner (get it in writing)
Zoning compliance permit House in a designated Flood Hazard Area Installer or homeowner
Photos, description, estimate, notarized affidavits Flood-zone work on an existing building Installer prepares; owner and contractor each sign
Building permit through CITY SQUARED Every solar job Installer
Electrical permit for the battery, if separate Backup quote accepted Ask the Building Department
Eversource interconnection application and meter swap Every grid-tied job Installer
Energy Storage Solutions enrollment Battery enrolled in the state program Installer, if it is an Eligible Contractor

The 50% test counts two years of work against the field-card value

In a mapped flood zone, one rule can turn a solar job into a far bigger project. Waterford calls it substantial improvement. Under §25.3.2.29 of the zoning regulations, it means any combination of work within a two-year period whose cumulative cost reaches 50% of the structure's market value before the work started. A roof replaced last year and a kitchen planned for next year can land in the same total as your solar job.

Two definitions in the same regulations set the numbers:

  • Market value (§25.3.2.22) is the appraised building value on the Assessor's Field Card before the first improvement. The field card is the town's record for your property, viewable in Waterford's online assessment database. Use the appraised building value, not the assessed value (which is 70% of fair market value), and leave out the land.
  • Cost (§25.3.2.9) is set by a detailed written contractor's estimate. It includes materials, utility and service equipment, utility meters, labor, overhead and profit. It excludes plans, surveys, permit fees, outside improvements and detached structures.

The flood-zone packet lists electrical wiring and service equipment among included costs. Neither document names solar panels or batteries. Before you sign, ask the Zoning Official whether the array, the battery and the subpanel count toward the total.

Crossing 50% has a real consequence. Under §25.3.5(D)(1), a substantially improved house must meet the flood rules for new construction, including a lowest floor, basement included, at least 1 foot above base flood elevation. For an existing house that sits lower, meeting that rule is a project far larger than solar.

Illustrative calculation, Waterford flood-zone home. The dollar figures are invented to show the method; the rule is Waterford's. Appraised building value on the field card: $260,000 (illustrative). 50% = $130,000 within any two-year period.

Work within two years Cost (illustrative)
Roof replaced 10 months ago $19,000
Quote A: 9.6 kW DC solar only $28,500
Quote B: 13.5 kWh battery + critical-loads subpanel $15,900
Kitchen remodel planned for next spring $70,000
Total $133,400 = 51.3%, over the line

Move the kitchen outside the two-year window and the total is $63,400 = 24.4%. If the Zoning Official does not count the array and battery as building cost, the roof and kitchen alone are $89,000 = 34.2%.

Three things follow. Keep Quote A and Quote B as separate lines, so the official can count each one or leave it out. List every project from the last two years and the next two before anyone signs. And if the total nears half the field-card value, change the timing of the other work before you shrink the solar design. In the example, the kitchen is the swing item.

Watch one date. Waterford's assessments reflect the October 1, 2022 revaluation. A 2026 revaluation is under way, with values finalized in late January 2027. If you file after that, ask the Zoning Official which field-card value applies, because the denominator in the test may change.

Check the solar price per watt with the battery taken out

In Waterford, the solar-only line does three jobs. It is the building-permit fee base, a line in the two-year flood total, and the number you test for a fair price. That last test only works if the battery is out of it.

Two terms first:

  • DC kW is the panels' total rated capacity in kilowatts. A 9.6 kW DC system is 9,600 watts of panels.
  • Price per watt ($/W) is the solar price divided by those DC watts.

The common mistake is dividing a combined price by panel watts. A battery adds thousands of dollars and no panel watts, so the result looks badly overpriced even when the solar part is fair.

Illustrative calculation, quote check against the State benchmark. A combined proposal of $44,400 for 9.6 kW DC with a 13.5 kWh battery: $44,400 ÷ 9,600 W = $4.63/W. Take out the battery ($13,500, the price EcoGen models for a 13.5 kWh battery) and the critical-loads subpanel ($2,400, illustrative). Solar only: $28,500 ÷ 9,600 W = $2.97/W.

State benchmark: EcoGen's Connecticut solar cost benchmark is $2.80/W, a modeled installed price before incentives (EcoGen Solar Cost Index, Connecticut, September 2026 Edition, prices as of Sept 25, 2026). EcoGen puts typical written quotes at $2.46–$3.14/W. At 9.6 kW the benchmark works out to $26,880, so $2.97/W sits inside the band, about 6% above the benchmark.

Expected output at EcoGen's statewide factor of 1,294 kWh per kW per year: 9.6 kW × 1,294 ≈ 12,400 kWh a year (illustrative calculation). That is a statewide model, not an estimate for your roof.

A benchmark is a model, not a quote. EcoGen itself cautions against comparing a solar-only benchmark with a battery-inclusive or financed quote without accounting for the difference. Before you divide, take out the battery, any backup subpanel or transfer equipment, roof work and any main-panel upgrade. Divide by the DC watts printed on the quote, not by a rounded system size from the sales conversation.

A quote at $4.63/W that turns out to be $2.97/W once the battery is out isn't overpriced. A quote that stays well above the band after you strip those lines deserves a written reason for the difference, item by item.

Backup for selected circuits, placed above flood risk

Some installer pages describe backup only as a "whole-home battery". That is one design among several. The alternative is backup for a chosen list of circuits, called critical loads: what must run in an outage, such as the refrigerator, sump pump, well pump, boiler or furnace controls, a medical device, Wi-Fi and some lights. Everything else stays off until the grid returns.

A backup quote should state four things in plain numbers:

  • Usable kWh: the energy the battery can actually deliver, which sets runtime.
  • Continuous kW: how much load it can carry at once.
  • Surge kW: the brief burst it can supply when a motor starts. Sump and well pumps need it.
  • Runtime assumptions: the starting charge, the reserve setting, the load list, and the runtime with and without solar recharge.

In a Waterford flood-zone house, the size of that list has a second cost. If the Zoning Official counts the battery and subpanel in the two-year total, every kWh you add to Quote B also adds to the number you are trying to keep under 50%. A short, deliberate critical-loads list is cheaper twice. To sketch your own list before you talk to an installer, use the backup planner on our homepage.

Where the equipment goes in a flood zone

In a flood hazard area, Waterford's §25.3.5(A)(2) requires electrical and other service equipment to be designed or located so that water cannot enter or collect in its components during a flood. Section 25.3.5(E)(3) prohibits electrical utility connections below base flood elevation in enclosed areas of elevated buildings.

That matters because the usual candidate spots, a basement or a garage, can sit low. Ask the installer to state, in the quote:

  • the battery and inverter location;
  • its height relative to BFE;
  • that the manufacturer allows installation there.

Whether equipment may sit below BFE in an existing house that isn't substantially improved is the Zoning Official's call. Get that answer in writing before the battery is ordered.

Who connects it to your panel

The Department of Consumer Protection sets the split. Holders of the PV-1 and PV-2 solar licenses may not connect to any existing panel, junction box, wiring or circuit. Connecting to the house's existing electrical system or meter is E-1 or E-2 electrician work. A critical-loads subpanel means moving circuits out of your main panel, so the backup quote should name who holds the E-1 or E-2 license. The same guidance also calls for Home Improvement Contractor registration. Check each license and registration with the state before you sign.

Event reserve versus outage reserve

As an Eversource customer, you can enroll a battery in Connecticut's Energy Storage Solutions program (ESS) through an Eligible Contractor. For enrollments from April 1, 2026, it pays $30 per kWh upfront, or $130 per kWh at Grid Edge locations. On top of that, it pays $300 per kW per year for ten years, based on how much power the battery actually delivers during grid events. Expect about 50 summer and 5 winter events a year.

Those payments pull against the reason you bought the battery. A battery discharged for a grid event has less left for an outage that evening. Ask the backup quote to state the reserve setting, the share of charge held back for you, and how that changes runtime. Ask too whether your address is in an Eversource Grid Edge area. This page has not checked any Waterford address.

Eversource and the 2026 Netting or Buy-All choice

Connecticut's Office of Consumer Counsel lists the towns served by their own electric utility, and Waterford is not one of them. Your power is delivered by Eversource (Connecticut Light & Power). Confirm it on your bill. That keeps both state programs on this page open to you: RRES for the panels and ESS for a battery.

Some installer pages still say "net metering". Eversource customers applying in 2026 instead choose between two options under the state's Residential Renewable Energy Solutions program (RRES):

Netting Buy-All
What you're paid (applications in 2026) Exported kWh credited at the full retail rate, minus a $0.0402/kWh charge on all production $0.3289/kWh for all production
Power you use at home Offsets your bill directly (the production charge still applies) All production is sold, so you keep buying your usage from the grid
How long the choice lasts Made at interconnection, fixed for 20 years; systems up to 25 kW Same

The 2026 rates come from the Public Utilities Regulatory Authority's December 17, 2025 decision. Rates for 2027 are not yet set as of November 18, 2026. Public Act 26-127 extends RRES through December 31, 2028, or until PURA launches successor programs if that comes sooner.

Timing matters more in Waterford's flood zone than elsewhere in town. A flood-zone job adds a zoning compliance permit and notarized affidavits before the building permit. If your project slips into 2027, it may enroll under 2027 rates that nobody can quote you yet. Ask the installer what date the Eversource application would go in, and what happens to the numbers if it misses the year.

Because the election lasts 20 years, ask the quote to show first-year value both ways, worked from your own 12 months of usage, and to say which option it recommends and why. EcoGen lists Eversource's solar fees as a $163 application fee and a $230 meter fee, plus a separate $200 interconnection application fee. Ask whether the quote includes them.

The federal credit is gone. The IRS says the Residential Clean Energy Credit is not available for property placed in service after December 31, 2025, batteries of 3 kWh or more included. What counts is when the installation is completed; the payment date doesn't matter. A quote that still subtracts a 30% federal credit is out of date. In 2026, the program money for a Waterford homeowner is RRES for solar and ESS for a battery.

What the two proposed quotes would contain

New London Solar is a proposed service, and coverage of Waterford is proposed and not yet confirmed. The two-quote approach (Proposed service) would start with a short assessment. You'd bring 12 months of usage and your Eversource bill. The assessment would review the roof and shade, the main panel and its spare spaces, your critical-loads list, and candidate battery locations, including flood exposure. It would then deliver two separate written quotes.

Line Quote A: solar only (Proposed service) Quote B: backup for selected circuits (Proposed service, optional)
What it covers Roof layout, panel count, DC kW, module and inverter models Critical-loads list, circuit by circuit, and what stays off
Output and capacity Annual kWh estimate with stated shade assumptions Usable kWh, continuous kW, surge kW, runtime assumptions
Price Total and price per DC watt Battery, subpanel or transfer work, each on its own line
Waterford use Solar line for the CITY SQUARED estimate and the 50% total Its own line in the 50% total; equipment height relative to BFE
Paperwork RRES Netting or Buy-All election; who files the permit and the Eversource application ESS enrollment, reserve setting, who makes the E-1/E-2 connection

Both would come with a circuit map, a labeled panel schedule marking the backed-up circuits, and the responsibility sheet from the permit section (Proposed service). Roof repair or a main-panel upgrade would each be a separate line, never folded into the solar price.

In Waterford, the split pays off in three places. The Zoning Official can see what each part adds to the two-year total. You can run the price-per-watt check on Quote A alone. And you can settle where the battery goes, or drop it, without reopening the solar design or its permit.

Waterford quote checklist: questions before you sign

Use these with every installer you talk to, alongside the quote checklist on this site.

  1. Flood status. Is any part of the house, attached garage or deck in a mapped flood zone, and has the Zoning Official confirmed it?
  2. Flood packet. In a flood hazard area, who files the zoning compliance permit, who prepares the photos, description and estimate, and will the contractor sign a notarized affidavit alongside yours?
  3. CITY SQUARED. Who files the building permit, and does the battery need a separate electrical permit?
  4. Separate lines. Are solar, battery, subpanel, roof work and any panel upgrade each priced on their own line?
  5. Two-year total. What work falls in the last two years and the next two? Does the Zoning Official count the array and battery, and which field-card value applies after late January 2027?
  6. Price per watt. What is the solar-only price divided by DC watts, and where does it fall against the State benchmark band?
  7. Equipment height. Where will the battery and inverter go, how high is that above base flood elevation, and does the manufacturer allow that spot?
  8. Panel connection. Who holds the E-1 or E-2 license for the subpanel work, and is the company registered as a Home Improvement Contractor?
  9. Reserve. If the battery joins ESS, is the installer an Eligible Contractor, what reserve is kept for outages, and how does that change runtime?
  10. RRES election and date. Netting or Buy-All, in writing, with first-year value shown both ways, and the date the Eversource application would be filed.
  11. Roof. How old is the roof, and is any roof work a separate line? A re-roof now also lands in the two-year total.
  12. After the install. Who honors which warranty, the installer or the manufacturer, and who services the system if it stops producing?